Doug Fleenor Design - Specifications


	(805) 481-9599

ISOLATORS
Inline isolator
Isolation amplifiers
DIN-rail isolator

SPLITTERS
Standard 3, 5 or 11 output
Enhanced five output
Enhanced wall mount
Bi-directional hub / RDM
Electronic patch bay

SIGNAL ROUTERS
Electronic patch bay
Passive A/B switches

WIRELESS DMX512
Marconi TX
Marconi Splitter
Marconi LV

MERGERS
Enhanced 2,3,4,5 or 6 input
Enhanced wall mount

POWER SUPPLIES
LED300: 24V 300W
LED100: Battery & Wireless
Class 2 Transformer

WALL PLATES
Passive XLR plates
Buffered DMX512 plates

MOUNTING OPTIONS
Rack kits
Product mounted in J-Box

DIMMERS
DMX8DIM - 8 Channel Dimmer

CUSTOM & OEM
Click Here

RELAYS
1 Ch. line voltage
6 Ch. line voltage
2 Ch. low voltage contacts
6 Ch. low voltage contacts

INTERFACES
Analog to DMX 48 channel
  RS-232 to DMX
  DMX to DMX
  DMX to AMX192
DMX to Analog 24 & 96 channel
DMX to CMX / CMX to DMX
  DMX to Strand D54
  DMX to DALI
  DMX to Microplex/LMX/Ultraplex
  DMX to RS-232
  DMX to Solid State Relay 96 Ch.
  DMX iPlayer interface
  DIN-rail mounted
  Pork Chopper - Hog II Overdrive
  Start Code Stripper

CONSOLES
Apathy: Single channel console
  Preset 10 architectural
  Preset 10 architectural 2
  Preset 10 portable
  RAD: Remote Address Device
  Rerun architectural
  Rerun portable
  Rerun rack mount
  Entry Station Two

DMX TESTERS
DMX512 Line Tester
GIZMO: DMX512 test box

OTHER DMX STUFF
XLR Terminator w/ LED
XLR Economy terminator
RJ45 Terminator

Basic Specification
model: PRE10-A2

Connector:

Phoenix Contact MSTB series 3 position two part terminal block
Model: MSTB 2,5/3-ST-5,08 Order Number: 17 57 02 2

Phoenix Contact MSTB series 5 position two part terminal block
Model: MSTB 2,5/5-ST-5,08 Order Number: 17 57 04 8

Connector pin out:

1 (C) DMX512 common
2 ( -) DMX512 data - (input)
3 (+) DMX512 data + (input)

1 (C) DMX512 common
2 ( -) DMX512 data - (output)
3 (+) DMX512 data + (output)
4 (C) Supply common (internally tied to pin1)
5 (V) Supply voltage “hot”

Input/Output circuit:

ESD protected EIA-485 transceiver (LT1785)

Indicators:

Ten green preset indicator LEDs
One yellow “Grand Master 100%” indicator LED
One yellow “Grand Master 0%” indicator LED
One yellow Fade Time LED
One red Signal / Record LED

User controls:

Ten preset push buttons
One “Grand Master Up” push button
One “Grand Master Down” push button
One recessed record push button
One recessed fade time push button

Option jumpers:

For a single station installation all jumpers should be installed.

	INSTALLED	REMOVED
JP1	Recording Enabled	Recording Disabled
JP2	Master Station	Slave Station
JP3	Fade to last active preset	Hold Last Look
JP4	Single Station Mode	Multi Station Mode
JP5	Switch Over Mode	Highest Takes Precedence (HTP) Mode
JP6	Radio Button Mode	Push On Push Off Mode

Power input:

9 to 16 volts AC or DC / 150 mA per station
(A 10 volt class "doorbell" transformer is recommended for fixed installations)

Color:

Black anodized with L.A.S.E.R engraved nomenclature

Size :

Faceplate: 4.5"h X 4.6"w X 0.2"d
Faceplate rear inset: 4.15"h X 4.25"w X 0.1"d
Electrical box minimum inside dimensions: 3.6"h X 2.9"w X 1.26"d

Doug Fleenor Design is a proud member of:

Doug Fleenor Design, Inc.
396 Corbett Canyon Road
Arroyo Grande, CA 93420
USA