SPLITTERS
  Standard 3, 5 or 11 output 
  Enhanced five output
  Enhanced wall mount
  Bi-directional hub / RDM
  Electronic patch bay

SIGNAL ROUTERS
  Electronic patch bay
  Passive A/B switches

WIRELESS DMX512
  Marconi TX
  Marconi Splitter
  Marconi LV

MERGERS
  Enhanced 2,3,4,5 or 6 input
  Enhanced wall mount

POWER SUPPLIES
  24V 300W LED
  Battery Wireless LED
  Class 2 Transformer

WALL PLATES
  Passive XLR plates
  Buffered DMX512 plates

MOUNTING OPTIONS
  Rack kits
  Product mounted in J-Box

CUSTOM & OEM
  Click Here

INTERFACES
  Analog to DMX 48 channel
  RS-232 to DMX
  DMX to AMX192
  DMX to Analog 24 & 96 channel
  DMX to CMX / CMX to DMX
  DMX to Strand D54 
  DMX to DALI
  DMX to Microplex/LMX/Ultraplex
  DMX to RS-232
  DMX to Solid State Relay 96 Ch.
  DMX iPlayer interface
  DIN-rail mounted
  Pork Chopper - Hog II Overdrive
  Start Code Stripper

CONSOLES
  Single channel "Apathy"
  Preset 10 architectural
  Preset 10 architectural 2
  Preset 10 portable
  Remote Address Device
  Rerun architectural 
  Rerun portable 
  Rerun rack mount 
  Entry Station Two

DMX TESTERS
  DMX512 line tester
  GIZMO DMX512 test box

OTHER DMX STUFF
  XLR Terminator w/ LED
  XLR Economy terminator
  RJ45 Terminator

Basic Specification
model: LED100

Input signal: W-DMX signal from any W-DMX transmitter (i.e. Doug Fleenor Design's Marconi TX)
Input circuit: W-DMX 'pico' card from Wireless Solutions, AB
Frequency band: 2.4 GHz ISM band (2402 - 2479 MHz)
Antenna connector: Reverse polarity SMA connector
Supplied antenna: 2 dBi omni directional 2.4 GHz
DMX512 output: Slew rate limited EIA-485 driver. All 512 channels.
LED fixture output: DMX512 timings and protocol with 24V single ended signal (for ColorBlast and Spectra PAR)
Output connectors: LED fixture: Gold plated 4 pin female XLR (Neutrik D-1 series) rated at 10 amps
DMX512: Gold plated 5 pin female XLR (Neutrik D-1 series)
Output pinouts: DMX512: LED Fixture:
   Pin 1: Common Pin 1: +24V
   Pin 2: Data - Pin 2: not used
   Pin 3: Data + Pin 3: Data
   Pin 4/5: Not used Pin 4: Common
Output current (power): 4.2 amps (100 watts) continuous
Run time: Single ColorBlast 12, Single Spectra PAR, or Two ColorBlast 6(from full charge)
   24 Hours on a rolling color fade (red to green to blue to red, etc.)
   18 Hours with one LED color on full (red or green or blue)
   12 Hours with two LED colors on full
   6 Hours with three LED colors on full (full white)
   Run time with two ColorBlast12 or two Spectra PAR is slightly less than half these times
Recharge time: 10 Hours from fully discharged batteries
   Recharge time is approximately equal to time of use (very roughly)
Charge type: 4 stage: Pulse (1.5A pulses), Constant current (1.5A), Constant voltage (28.8V), Float (27.6V)
Battery life: 1800 charge/discharge cycles at 30% discharge, 400 charge/discharge cycles at 100% discharge
Indicators: Red: POWER, Blue: ASSIGNED, Yellow: RF LINK, Green: DMX512
Charge indicator: Flashing: Pre-charge, Orange: Charging, Green: Charged
   Three digit DMX Start Address and Voltmeter display
User controls: On/off toggle switch, DC Rated 20A
   Three push buttons to set DMX Start Address
  One push button to activate Voltmeter
One (recessed) configure push button
Fixture mounting: One top mounted 1/2-13 nut with 1/2-13 bolt and washer supplied
Color: Black with white silkscreen nomenclature
Size and weight: 8.5"h X 6.5"d X 9.5"w, 29 pounds
Mounting options: Two 1/2" holes for half couplers or “C” Clamps

Doug Fleenor Design is a proud member of: