 |
 |
 |
(805) 481-9599 |
||
     |
||
Inline isolator
Isolation amplifiers
DIN-rail isolator
SPLITTERS
Standard 3, 5 or 11 output
Enhanced five output
Enhanced wall mount
Bi-directional hub / RDM
Electronic patch bay
SIGNAL ROUTERS
Electronic patch bay
Passive A/B switches
WIRELESS DMX512 
Marconi TX
Marconi Splitter
Marconi LV
MERGERS
Enhanced 2,3,4,5 or 6 input
Enhanced wall mount
POWER SUPPLIES
LED600: 24V 600W
LED300: 24V 300W
LED100: Battery & Wireless
Class 2 Transformer
WALL PLATES
ColorWheel
Passive XLR plates
Buffered DMX512 plates
MOUNTING OPTIONS
Rack kits
Product mounted in J-Box
DIMMERS
DMX8DIM - 8 Channel NEMA1
DMX24DIM - 24 Channel Rackmount
1 Ch. line voltage
6 Ch. line voltage
2 Ch. low voltage contacts
6 Ch. low voltage contacts
INTERFACES
Analog to DMX 48 channel
RS-232 to DMX
DMX Decelerator
DMX to DMX
DMX to AMX192
DMX to Analog 24 & 96 channel
DMX to CMX / CMX to DMX
DMX to Strand D54
DMX to DALI
DMX to Microplex/LMX/Ultraplex
DMX to RS-232
DMX to Solid State Relay 96 Ch.
DMX iPlayer interface
DIN-rail mounted
Pork Chopper - Hog II Overdrive
Start Code Stripper
CONSOLES
Apathy: Single channel console
Preset 10 architectural
Preset 10 architectural 2
Preset 10 portable
RAD: Remote Address Device
Rerun architectural
Rerun portable
Rerun rack mount
Entry Station Two
DMX TESTERS
DMX512 Line Tester
GIZMO: DMX512 test box
OTHER DMX STUFF
XLR Terminator w/ LED
XLR Economy terminator
RJ45 Terminator
Basic Specification
model: DMX2iPLAY
| Input baud rate: | 250 Kb/s |
| Input circuit: | ESD protected EIA-485 transceiver (LT1785) |
| Input signal: | 3 volts minimum, 12 volts maximum |
| Input connectors: |
Gold plated 5 pin Neutrik D-1. |
| Through connector: | Gold plated female 5 pin XLR (Neutrik D-1 series). All pins wired through. |
| DMX profile: | 3 consecutive channels (trigger mode, show selection, global intensity) OR 5 consecutive channels (trigger mode, hundreds, ten, ones, global intensity) NOTE: Contact Doug Fleenor Design for more information on this mode |
| Output baud rate: | 9600 bps, 8 data bits, no parity, 1 stop bit |
| Output circuit: | RS-232 driver (MAX232) Outputs are short circuit protected but not over voltage protected. |
| Output signal: | RS-232 driver yields an approximate +/- 10 volt signal |
| Output connector: | DB9 (male) Pin 2 = Receive, Pin 3 = Transmit, Pin 5 = signal ground. (straight DB9 Male to Female, cable provided) |
| User interface: | Start address set via a three digit thumbwheel switch |
| Indicators: | Red power LED, Green DMX signal LED, Green RS-232 transmit LED |
| Power input: | Universal power supply 100 - 240VAC, 50/60 hertz, 5 watts |
| Color: | Black anodized |
| Size and weight: |
Chassis 5.3" X 3.2"w X 1.8"h, 12 ounces Power supply 2.2"l X 1.9"w X 1.0"h, 5 ounces |
Doug Fleenor Design is a proud member of:
Doug Fleenor Design, Inc.
396 Corbett Canyon Road
Arroyo Grande, CA 93420
USA