 |
 |
 |
(805) 481-9599 |
||
     |
||
Inline isolator
Isolation amplifiers
DIN-rail isolator
SPLITTERS
Standard 3, 5 or 11 output
Enhanced five output
Enhanced wall mount
Bi-directional hub / RDM
Electronic patch bay
SIGNAL ROUTERS
Electronic patch bay
Passive A/B switches
WIRELESS DMX512 
Marconi TX
Marconi Splitter
Marconi LV
MERGERS
Enhanced 2,3,4,5 or 6 input
Enhanced wall mount
POWER SUPPLIES
LED300: 24V 300W
LED100: Battery & Wireless
Class 2 Transformer
WALL PLATES
Passive XLR plates
Buffered DMX512 plates
MOUNTING OPTIONS
Rack kits
Product mounted in J-Box
DIMMERS
DMX8DIM - 8 Channel Dimmer
1 Ch. line voltage
6 Ch. line voltage
2 Ch. low voltage contacts
6 Ch. low voltage contacts
INTERFACES
Analog to DMX 48 channel
RS-232 to DMX
DMX to DMX
DMX to AMX192
DMX to Analog 24 & 96 channel
DMX to CMX / CMX to DMX
DMX to Strand D54
DMX to DALI
DMX to Microplex/LMX/Ultraplex
DMX to RS-232
DMX to Solid State Relay 96 Ch.
DMX iPlayer interface
DIN-rail mounted
Pork Chopper - Hog II Overdrive
Start Code Stripper
CONSOLES
Apathy: Single channel console
Preset 10 architectural
Preset 10 architectural 2
Preset 10 portable
RAD: Remote Address Device
Rerun architectural
Rerun portable
Rerun rack mount
Entry Station Two
DMX TESTERS
DMX512 Line Tester
GIZMO: DMX512 test box
OTHER DMX STUFF
XLR Terminator w/ LED
XLR Economy terminator
RJ45 Terminator
Basic Specification
model: DMX96OC-EXTPS
| Input baud rate: | DMX512: 250 Kb/s |
| Input circuit: | EIA-485 receiver with series 100 ohm PTC self-resetting "fuses" clamped to +/- 7 volts by four low capacitance transorb diodes |
| Input signal: | 0.5 volts minimum, 12 volts maximum Input can withstand up to 120 volts without damage and transients up to 5KV |
| Output circuit: | 8-bit 50V 500mA NPN Darlington driver Unprotected output |
| Output signal: | VCE(SAT) 1.1V maximum at 100mA |
| Max. output current: | 100mA continuous, 500mA peak |
| Max. output voltage: | 48VDC |
| Input/output isolation: | Greater than 500 volts |
| Throughput delay: | Less than .005 seconds (DMX input change to output change) |
| DMX512 connectors: | Two gold plated 5 pin Neutrik D-1 Series (male input, female pass through) (All five pins are wired on the pass through) |
| Output connectors: | Four female DB-25 with gold plated pins Pin number equals output number, pin 25 is output common (900mA maximum on common maximum on pin 25) |
| Output common: | An "output common" terminal block is available for high current applications. |
| Power input: |
(Standard ) model: DMX96OC-EXTPS (Optional) model: DMX96OC |
| Color: | Top, bottom and sides: Silver hammer tone Front and back: Black |
| Size and weight: | 6.5" deep, 1.7" high, 16.5" wide, 6.5 pounds (19" rack adapter available) |
Doug Fleenor Design is a proud member of:
Doug Fleenor Design, Inc.
396 Corbett Canyon Road
Arroyo Grande, CA 93420
USA