 |
 |
 |
(805) 481-9599 |
||
     |
||
ISOLATORS
DMXOPTO: Inline isolator
121: Isolation amplifiers
DINTAP / DININTR: DIN-rail isolator
ETHERNET PRODUCTS
E2E: Ethernet to Ethernet
E1REL20A: 1 Ch. Ethernet Relay
E8ANL-DIN: 8 Ch. Ethernet to Analog
NODE: Ethernet/DMX Interfaces
NODE DISCOVERY
PRE10ETHER-A: Ethernet Preset 10
ES2ETHER: Ethernet Entry Station Two
SPLITTERS
Splitter Selection Matrix
123/125/1211: 3, 5 or 11 output
124: 4 output DMX / RDM splitter
125EE: Enhanced five output
125EE-WALL: Enhanced wall mount
127: 7 output DMX / RDM splitter
1212: 12 output DMX / RDM splitter on DIN rail
SIGNAL ROUTERS
RR: Electronic patch bay
SW: Passive A/B switches
WIRELESS DMX512
Marconi TX: Transmitter
Marconi SP: 3 way splitter
Marconi LV: Low voltage receiver
MERGERS
221E: Enhanced 2,3,4,5 or 6 input
221E-WALL: Enhanced wall mount
POWER SUPPLIES
LED600: 24V 600W
LED400: 24V 400W
LED300: 24V 300W
LED100: Battery & Wireless
XFMR: Class 2 Transformer
WALL PLATES
WP-O/WP-I: Passive XLR plates
DFDNET: Buffered DMX512 plates
FIXTURES
EDISON: 25 lamp arrayable
DIMMERS
DMX8DIM: 8 Channel NEMA1
DMX12DIM-ELV: 12 Channel
DMX24DIM: 24 Channel
RELAYS
DMX1REL20A: 1 Ch. line voltage
DMX6REL15A/-30A: 6 Ch. line voltage
DMX2REL5A: 2 Ch. low voltage
DMX6REL1A: 6 Ch. low voltage
E1REL20A: Ethernet Relay
INTERFACES
Analog to DMX 48 channel
RS-232 to DMX
DMXDECELERATORII
DMX to DMX
DMX to AMX192 192 Ch.
DMX to Analog 12 channel
DMX to Analog 96 channel
DMX to CMX / CMX to DMX
DMX to Strand D54
DMX to DALI
DMX to Microplex/LMX/Ultraplex
DMX to Solid State Relay 96 Ch.
DMX iPlayer interface
E8ANL-DIN: 8 Ch. Ethernet to Analog
Fire Alarm Interface
CONSOLES
APATHY: Single channel console
COLORWHEEL
PRESET 8 - DMX Snapshot Console
PRESET 10 - DMX Snapshot Console
PRESET 10 QUATTRO - 4 Universe
PRE10-A2: Preset 10 Architectural 2
PRESET 12 - DMX Snapshot Console
PRESET 18 - DMX Snapshot Console
PRE10ETHER-A: Ethernet Preset 10
RAD: RDM Address Device
RERUN - DMX Recorder
ES2: Entry Station Two
ES2ETHER: Ethernet Entry Station Two
DMX TESTERS
DMXdoohickey
DMXTSTR: DMX512 line tester
GIZMO: DMX512 test box
OTHER DMX STUFF
TERM: XLR Terminator w/ LED
T2: XLR Economy terminator
T-45: RJ45 Terminator
MOUNTING OPTIONS
RK: Rack Kits
JBOX: Product mounted in J-Box
CUSTOM & OEM
Click Here
Basic Specification
model: DMX96ANL
| Input baud rate: | DMX512: 250 Kb/s, CMX: 152.6 Kb/s |
| Input circuit: |
EIA-485 receiver with series 100 ohm PTC self resetting "fuses" clamped to +/- 7 volts by four low capacitance transorb diodes |
| Input signal: | 0.5 volts minimum, 12 volts maximum Input can withstand up to 120 volts without damage, transients up to 5KV |
| Output circuit: | LM324 quad op amp with 1N4004 series diode |
| Output signal: | 0 to 10.1 volts positive DC into 2000 ohm load Outputs can withstand up to positive 400 volts without damage Outputs cannot withstand high negative voltages |
| Max. output current: | 15 mA per output, 120 mA total all outputs (360 mA total on 96 out version) |
| Input/output isolation: | Greater than 500 volts |
| Throughput delay: | Less than .005 seconds (DMX input change to analog output change) |
| DMX512 connectors: |
Two gold plated 5 pin Neutrik D-1 Series (male input, female pass through) |
| Analog connector: | Female DB-25 with gold plated pins Pin number equals output number, pin 25 is output common |
| Power input: | 90 - 125 volts, 50/60 hertz, 10 watts (180 - 250 volts optional) |
| Color: |
Silver anodized aluminum |
| Size and weight: |
8.0" deep, 1.7" high, 16.7" wide, 4.5 pounds |
Doug Fleenor Design is a proud member of:
