 |
 |
 |
(805) 481-9599 |
||
     |
||
ISOLATORS
DMXOPTO: Inline isolator
121: Isolation amplifiers
DINTAP / DININTR: DIN-rail isolator
ETHERNET PRODUCTS
E2E: Ethernet to Ethernet
E1REL20A: 1 Ch. Ethernet Relay
E8ANL-DIN: 8 Ch. Ethernet to Analog
NODE: Ethernet/DMX Interfaces
NODE DISCOVERY
PRE10ETHER-A: Ethernet Preset 10
ES2ETHER: Ethernet Entry Station Two
SPLITTERS
Splitter Selection Matrix
123/125/1211: 3, 5 or 11 output
124: 4 output DMX / RDM splitter
125EE: Enhanced five output
125EE-WALL: Enhanced wall mount
127: 7 output DMX / RDM splitter
1212: 12 output DMX / RDM splitter on DIN rail
SIGNAL ROUTERS
RR: Electronic patch bay
SW: Passive A/B switches
WIRELESS DMX512
Marconi TX: Transmitter
Marconi SP: 3 way splitter
Marconi LV: Low voltage receiver
MERGERS
221E: Enhanced 2,3,4,5 or 6 input
221E-WALL: Enhanced wall mount
POWER SUPPLIES
LED600: 24V 600W
LED400: 24V 400W
LED300: 24V 300W
LED100: Battery & Wireless
XFMR: Class 2 Transformer
WALL PLATES
WP-O/WP-I: Passive XLR plates
DFDNET: Buffered DMX512 plates
FIXTURES
EDISON: 25 lamp arrayable
DIMMERS
DMX8DIM: 8 Channel NEMA1
DMX12DIM-ELV: 12 Channel
DMX24DIM: 24 Channel
RELAYS
DMX1REL20A: 1 Ch. line voltage
DMX6REL15A/-30A: 6 Ch. line voltage
DMX2REL5A: 2 Ch. low voltage
DMX6REL1A: 6 Ch. low voltage
E1REL20A: Ethernet Relay
INTERFACES
Analog to DMX 48 channel
RS-232 to DMX
DMXDECELERATORII
DMX to DMX
DMX to AMX192 192 Ch.
DMX to Analog 12 channel
DMX to Analog 96 channel
DMX to CMX / CMX to DMX
DMX to Strand D54
DMX to DALI
DMX to Microplex/LMX/Ultraplex
DMX to Solid State Relay 96 Ch.
DMX iPlayer interface
E8ANL-DIN: 8 Ch. Ethernet to Analog
Fire Alarm Interface
CONSOLES
APATHY: Single channel console
COLORWHEEL
PRESET 8 - DMX Snapshot Console
PRESET 10 - DMX Snapshot Console
PRESET 10 QUATTRO - 4 Universe
PRE10-A2: Preset 10 Architectural 2
PRESET 12 - DMX Snapshot Console
PRESET 18 - DMX Snapshot Console
PRE10ETHER-A: Ethernet Preset 10
RAD: RDM Address Device
RERUN - DMX Recorder
ES2: Entry Station Two
ES2ETHER: Ethernet Entry Station Two
DMX TESTERS
DMXdoohickey
DMXTSTR: DMX512 line tester
GIZMO: DMX512 test box
OTHER DMX STUFF
TERM: XLR Terminator w/ LED
T2: XLR Economy terminator
T-45: RJ45 Terminator
MOUNTING OPTIONS
RK: Rack Kits
JBOX: Product mounted in J-Box
CUSTOM & OEM
Click Here
Basic Specification
model: 2322DMX
DMX data rate: 250 Kb/s
DMX circuit: ESD protected EIA-485 transceiver (LT1785)
DMX signal: Fully opto-isolated, bi-directional
DMX connectors: Gold plated male 5 pin XLR (Neutrik D-1 series).
Gold plated female 5 pin XLR (Neutrik D-1 series). All pins wired through.
Pin 1 = common, Pin 2 = Data-, Pin 3 = Data+.
RS-232 data rate: 9600 bps, 8 data bits, 1 start bit, 1 stop bit, no parity
RS-232 circuit: RS-232 driver (MAX232)
Outputs are short circuit protected but not over voltage protected.
RS-232 signal: RS-232 driver yields an approximate +/- 10 volt signal
RS-232 connector: DB9 (male)
Pin 2 = receive, Pin 3 = transmit, Pin 5 = common, Pin 7 = RTS, Pin 8 = CTS
(DB9 Female to Female, null modem cable provided)
Gold plated female 3 pin XLR (Neutrik D-1 series).
Pin 1 = common, Pin 2 = receive, Pin 3 = transmit.
User interface: Start address set via a three digit thumbwheel switch
Indicators: Red power LED, Green DMX signal LED, Green MIMIC LED
Power input: 100 - 120 volts, 50/60 hertz, 12 watts (208-240 volt optional)
Color: Silver hammertone with black front and back panels
Size and weight: 6.5" deep, 1.7" high, 8.25" wide 3.3 pounds (19" rack kits available)
Doug Fleenor Design is a proud member of:
