dr2
Main image
dr1
(805) 481-9599
ProductsPricingDMX InfoFun StuffContact DFD
ISOLATORS
  Inline isolator
  Isolation amplifiers
  DIN-rail isolator

SPLITTERS
  Standard 3, 5 or 11 output 
  Enhanced five output
  Enhanced wall mount
  Bi-directional hub / RDM
  Electronic patch bay

SIGNAL ROUTERS
  Electronic patch bay
  Passive A/B switches

WIRELESS DMX512 W-DMX LOGO
  Marconi TX
  Marconi Splitter
  Marconi LV

MERGERS
   Enhanced 2,3,4,5 or 6 input
  Enhanced wall mount

POWER SUPPLIES
   LED600: 24V 600W
  LED300: 24V 300W
  LED100: Battery & Wireless
  Class 2 Transformer

WALL PLATES
   ColorWheel
  Passive XLR plates
  Buffered DMX512 plates

MOUNTING OPTIONS
  Rack kits
  Product mounted in J-Box

DIMMERS
  DMX8DIM - 8 Channel NEMA1
  DMX24DIM - 24 Channel Rackmount

CUSTOM & OEM
  Click Here

 

 RELAYS
  1 Ch. line voltage
  6 Ch. line voltage
  2 Ch. low voltage contacts
  6 Ch. low voltage contacts

INTERFACES
  Analog to DMX 48 channel
  RS-232 to DMX
   DMX Decelerator
  DMX to DMX
  DMX to AMX192
  DMX to Analog 24 & 96 channel
  DMX to CMX / CMX to DMX
  DMX to Strand D54 
  DMX to DALI
  DMX to Microplex/LMX/Ultraplex
  DMX to RS-232
  DMX to Solid State Relay 96 Ch.
  DMX iPlayer interface
  DIN-rail mounted
  Pork Chopper - Hog II Overdrive
  Start Code Stripper

CONSOLES
  Apathy: Single channel console
  Preset 10 architectural
  Preset 10 architectural 2
  Preset 10 portable
  RAD: Remote Address Device
  Rerun architectural 
  Rerun portable 
  Rerun rack mount 
  Entry Station Two

DMX TESTERS
  DMX512 Line Tester
  GIZMO: DMX512 test box

OTHER DMX STUFF
  XLR Terminator w/ LED
  XLR Economy terminator
  RJ45 Terminator

 

Basic Specification
model: RERUN-A

SPECIFICATIONS
Connector:

Terminal block #1
Phoenix Contact MSTB series
5 position two part terminal block
Model: MSTB 2,5/5-ST-5,08
Order number: 17 57 04 8

 Terminal block #2
Phoenix Contact MSTB series
3 position two part terminal block
Model: MSTB 2,3-G-5,08
Order number: 17 55 74 9
Connector pin out:

Terminal Block #1 (DMX512 Output)
1 (C) DMX512 common
2 ( -) DMX512 data -
3 (+) DMX512 data +
4 (C) Supply common
(internally tied to pin1)
5 (V) Supply voltage "hot"

 Terminal Block #2 (DMX512 Input)
1 (C) DMX512 common
2 ( -) DMX512 data -
3 (+) DMX512 data +
Input circuit:

ESD protected EIA-485 transceiver (LT1785)
Output circuit: ESD protected EIA-485 transceiver (LT1785)
Isolation: None. DMX input is not isolated from DMX output.
Indicators:

Ten green SHOW LEDs
One green PAUSE LED
One green LOOP LED
One yellow START LED
One yellow END LED
One red INPUT/RECORD LED
User controls:

Ten [SHOW] buttons
One [PAUSE] button
One [LOOP] button
One [REWIND] button
One [FORWARD] button
One recessed [RECORD] button
Option jumpers:
INSTALLED REMOVED
JP1 Recording enabled Recording/editing disabled
JP2 Run show on DMX512 loss Hold last look on DMX512 loss
JP3 Normal operation Run hardware test
JP4 Normal operation Disable operation
JP5 Switch Over Mode Highest Takes Precedence (HTP) Mode
JP6 Normal operation Erase Memory (DANGER!)
Power input:

10 to 15 volts AC or DC / 150mA per station
(A 10 volt class 2 "doorbell" transformer is recommended for fixed installations)
Color: Black anodized, with silver engraved nomenclature
Size :

Faceplate: 4.5"h X 4.6"w X 0.2"d
Faceplate rear inset: 4.15"h X 4.25"w X 0.1"d
Electrical box minimum inside dimensions: 2.9"h X 3.5"w X 1.5"d

Doug Fleenor Design is a proud member of:

TEA

Doug Fleenor Design, Inc.
396 Corbett Canyon Road
Arroyo Grande, CA 93420
USA