 |
 |
 |
(805) 481-9599 |
||
     |
||
Inline isolator
Isolation amplifiers
DIN-rail isolator
SPLITTERS
Standard 3, 5 or 11 output
Enhanced five output
Enhanced wall mount
Bi-directional hub / RDM
Electronic patch bay
SIGNAL ROUTERS
Electronic patch bay
Passive A/B switches
WIRELESS DMX512 
Marconi TX
Marconi Splitter
Marconi LV
MERGERS
Enhanced 2,3,4,5 or 6 input
Enhanced wall mount
POWER SUPPLIES
LED600: 24V 600W
LED300: 24V 300W
LED100: Battery & Wireless
Class 2 Transformer
WALL PLATES
ColorWheel
Passive XLR plates
Buffered DMX512 plates
MOUNTING OPTIONS
Rack kits
Product mounted in J-Box
DIMMERS
DMX8DIM - 8 Channel NEMA1
DMX24DIM - 24 Channel Rackmount
1 Ch. line voltage
6 Ch. line voltage
2 Ch. low voltage contacts
6 Ch. low voltage contacts
INTERFACES
Analog to DMX 48 channel
RS-232 to DMX
DMX Decelerator
DMX to DMX
DMX to AMX192
DMX to Analog 24 & 96 channel
DMX to CMX / CMX to DMX
DMX to Strand D54
DMX to DALI
DMX to Microplex/LMX/Ultraplex
DMX to RS-232
DMX to Solid State Relay 96 Ch.
DMX iPlayer interface
DIN-rail mounted
Pork Chopper - Hog II Overdrive
Start Code Stripper
CONSOLES
Apathy: Single channel console
Preset 10 architectural
Preset 10 architectural 2
Preset 10 portable
RAD: Remote Address Device
Rerun architectural
Rerun portable
Rerun rack mount
Entry Station Two
DMX TESTERS
DMX512 Line Tester
GIZMO: DMX512 test box
OTHER DMX STUFF
XLR Terminator w/ LED
XLR Economy terminator
RJ45 Terminator
Basic Specification
model: RR (Rotor-Routor)
|
Input module
|
|
| Input circuit: | EIA-485 receiver with 120 ohm termination resistor between +Data and -Data. |
| Input connectors: | Gold plated 5 pin male Neutrik D-1 series (3 pin or terminal connections are optional). |
| Output circuit: | EIA-485 transmitter with 60 ohm series (source) termination (DMX512 signals on a non-standard connector). |
| Output connector: | DB-25P.(male) |
|
Output module
|
|
| Input circuit: | EIA-485 receiver. A termination plug is required if the output module is separated from the input module by more than six feet. |
| Input connector: | DB-25P (male) |
| Output circuit: | EIA-485 transmitter
NOTE: This product uses a slew-rate-limited output drivers. Slew-rate-limited drivers minimize EMI and reduce reflections caused by improperly terminated cables. |
| Output connectors: | Gold plated 5 pin female Neutrik D-1 series (3 pin or terminal connections are optional) |
|
DB-25 pinouts
|
|
| input #: | 1 2 3 4 5 6 7 8 9 10 11 12 |
| data - pin #: | 14 15 16 17 18 19 20 21 22 23 24 25 |
| data + pin #: | 2 3 4 5 6 7 8 9 10 11 12 13 |
| pin 1 is circuit common |
|
|
Common specifications
|
|
| Isolation: | 2500 volt optical coupler, 1500 volt split bobbin transformer |
| Power input: | 100 - 120 volts, 50/60 hertz, 12 watts (208 - 240 volt optional) |
| Size & weight: | 1.74" high, 19" wide, 12" deep, 9 pounds (19" rack adapter is provided). |
Doug Fleenor Design is a proud member of:
Doug Fleenor Design, Inc.
396 Corbett Canyon Road
Arroyo Grande, CA 93420
USA