 |
 |
 |
(805) 481-9599 |
||
     |
||
Inline isolator
Isolation amplifiers
DIN-rail isolator
SPLITTERS
Standard 3, 5 or 11 output
Enhanced five output
Enhanced wall mount
Bi-directional hub / RDM
Electronic patch bay
SIGNAL ROUTERS
Electronic patch bay
Passive A/B switches
WIRELESS DMX512 
Marconi TX
Marconi Splitter
Marconi LV
MERGERS
Enhanced 2,3,4,5 or 6 input
Enhanced wall mount
POWER SUPPLIES
LED300: 24V 300W
LED100: Battery & Wireless
Class 2 Transformer
WALL PLATES
Passive XLR plates
Buffered DMX512 plates
MOUNTING OPTIONS
Rack kits
Product mounted in J-Box
DIMMERS
DMX8DIM - 8 Channel Dimmer
1 Ch. line voltage
6 Ch. line voltage
2 Ch. low voltage contacts
6 Ch. low voltage contacts
INTERFACES
Analog to DMX 48 channel
RS-232 to DMX
DMX to DMX
DMX to AMX192
DMX to Analog 24 & 96 channel
DMX to CMX / CMX to DMX
DMX to Strand D54
DMX to DALI
DMX to Microplex/LMX/Ultraplex
DMX to RS-232
DMX to Solid State Relay 96 Ch.
DMX iPlayer interface
DIN-rail mounted
Pork Chopper - Hog II Overdrive
Start Code Stripper
CONSOLES
Apathy: Single channel console
Preset 10 architectural
Preset 10 architectural 2
Preset 10 portable
RAD: Remote Address Device
Rerun architectural
Rerun portable
Rerun rack mount
Entry Station Two
DMX TESTERS
DMX512 Line Tester
GIZMO: DMX512 test box
OTHER DMX STUFF
XLR Terminator w/ LED
XLR Economy terminator
RJ45 Terminator
Basic Specification
model: DMX24ANL
| Input baud rate: | DMX512: 250 Kb/s, CMX: 152.6 Kb/s |
| Input circuit: |
EIA-485 receiver with series 100 ohm PTC self resetting "fuses" clamped to +/- 7 volts by four low capacitance transorb diodes |
| Input signal: | 0.5 volts minimum, 12 volts maximum Input can withstand up to 120 volts without damage, transients up to 5KV |
| Output circuit: | LM324 quad op amp with 1N4004 series diode |
| Output signal: | 0 to 10.1 volts positive DC into 2000 ohm load Outputs can withstand up to positive 400 volts without damage Outputs cannot withstand high negative voltages |
| Max. output current: | 15 mA per output, 120 mA total all outputs (360 mA total on 96 out version) |
| Input/output isolation: | Greater than 500 volts |
| Throughput delay: | Less than .005 seconds (DMX input change to analog output change) |
| DMX512 connectors: |
Two gold plated 5 pin Neutrik D-1 Series (male input, female pass through) |
| Analog connector: | Female DB-25 with gold plated pins Pin number equals output number, pin 25 is output common |
| Power input: | 90 - 125 volts, 50/60 hertz, 10 watts (180 - 250 volts optional) |
| Color: |
Black front, back, top, and sides. Clear iridite aluminum bottom |
| Size and weight: |
9.0" deep, 1.6" high, 5.6" wide, 2.5 pounds |
Doug Fleenor Design is a proud member of:
Doug Fleenor Design, Inc.
396 Corbett Canyon Road
Arroyo Grande, CA 93420
USA