dr2
Main image
dr1
(805) 481-9599
ProductsPricingDMX InfoFun StuffContact DFD

ISOLATORS
  DMXOPTO: Inline isolator
  121: Isolation amplifiers
  DINTAP / DININTR: DIN-rail isolator

ETHERNET PRODUCTS
  NODE4
  NODE2
  NODE1
  NODE DISCOVERY
  E2E: Ethernet to Ethernet

SPLITTERS
  123/125/1211: 3, 5 or 11 output
  125EE: Enhanced five output
  125EE-WALL: Enhanced wall mount
  124: 4 output DMX / RDM splitter
  BIDI8: DMX / RDM splitter

SIGNAL ROUTERS
  RR: Electronic patch bay
  SW: Passive A/B switches

WIRELESS DMX512 W-DMX LOGO
  Marconi TX: Transmitter
  Marconi SP: 3 way splitter
  Marconi LV: Low voltage receiver

MERGERS
  221E: Enhanced 2,3,4,5 or 6 input
  221E-WALL: Enhanced wall mount

POWER SUPPLIES
  LED600: 24V 600W
  LED400: 24V 400W
  LED300: 24V 300W
  LED100: Battery & Wireless
  XFMR: Class 2 Transformer

WALL PLATES
  WP-O/WP-I: Passive XLR plates
  DFDNET: Buffered DMX512 plates

FIXTURES
  EDISON: 25 lamp arrayable

DIMMERS
  DMX8DIM: 8 Channel NEMA1
  DMX12DIM-ELV: 12 Channel
  DMX24DIM: 24 Channel

MOUNTING OPTIONS
  RK: Rack Kits
  JBOX: Product mounted in J-Box

RELAYS
  DMX1REL20A: 1 Ch. line voltage
  DMX6REL15A/-30A: 6 Ch. line voltage
  DMX2REL5A: 2 Ch. low voltage
  DMX6REL1A: 6 Ch. low voltage

INTERFACES
  Analog to DMX 48 channel
  RS-232 to DMX
  DMX DECELERATOR
  DMX to DMX
  DMX to AMX192 192 Ch.
  DMX to Analog 12 channel
  DMX to Analog 96 channel
  DMX to CMX / CMX to DMX
  DMX to Strand D54
  DMX to DALI
  DMX to Microplex/LMX/Ultraplex
  DMX to Solid State Relay 96 Ch.
  DMX iPlayer interface
  NODE4: Ethernet to DMX
  Fire Alarm Interface

CONSOLES
  APATHY: Single channel console
  COLORWHEEL
  PRE8-A: Preset 8 Architectural
  PRE8-P: Preset 8 Portable
  PRE8-D: Preset 8 Desktop
  PRE10-A: Preset 10 Architectural
  PRE10-A2: Preset 10 Architectural 2
  PRE10-P: Preset 10 Portable
  RAD: RDM Address Device
  RERUN-A: Rerun Architectural
  RERUN-P: Rerun Portable
  RERUN-R: Rerun Rack Mount
  ES2: Entry Station Two

DMX TESTERS
  DMXTSTR: DMX512 line tester
  GIZMO: DMX512 test box

OTHER DMX STUFF
  TERM: XLR Terminator w/ LED
  T2: XLR Economy terminator
  T-45: RJ45 Terminator

CUSTOM & OEM
  Click Here

Basic Specification
model: 125EE



Baud rate: 0 to 250 Kilobaud
Input circuit: EIA-485 receiver protected by two self resetting fuses
120 ohm input terminator protected by a self resetting fuse
Four transorb diodes: two on +Data, two on -Data
Input signal: 0.5 volts minimum, 12 volts maximum
Input can withstand up to 120 volts without damage, transients up to 5KV
Output circuit: Slew rate limited EIA-485 driver protected by two self reseting Polyswitch fuses.
One transorb diode on +Data, one on -Data.
(Slew-rate-limited drivers minimize EMI and reduce reflections caused by improperly terminated cables)
Output signal:  EIA-485 driver yields an approximate 3 volt signal into 120 Ohms
Outputs can withstand up to 12 volts without damage, transients up to 5KV.
Connectors: Gold plated 5 pin Neutrik D-1 Series (male input, female outputs)
(3 pin connectors, terminal blocks, or RJ45 connectors optional)
Isolation: 2500 volt optical coupler, 5000 volt split bobbin transformer
Power input: 90 - 240 volts, 50/60 hertz, 0.1 amp (24 watts)IEC-320 (international) input connector
Color:  Silver hammertone with black front and back panels
Size & weight: 11.25" deep, 1.74" high, 8.25" wide, 5 pounds
(19" rack adapter available)

Wall Mount
2" deep, 8.5" high, 10.5" wide, 5 pounds
Mounting Hole Locations 6" Vertical 9.5" Horizontal

Doug Fleenor Design is a proud member of:

TEA